argreen Process Technologies | From Coarse Straining Down to Microfiltration, Reverse Osmosis and Ultra Filtration
Pargreen Process Technologies
1206 Capitol Drive
Addison, IL. 60101
USA

Call: 800.323.2810
Fax: 630.628.3050
Email: sales@pargreen.com
Website: www.pargreen.com
Print Back
Memtrex PM (MPM) filters' 100% polypropylene construction offers low extractables, long service life and broad chemical compatibility (Figure 1). Thermoplastic sealing techniques are used in the cartridge construction eliminating the need for glues or sealers which could leach contaminates. MPM filters are integrity testable. All components are made of FDA-acceptable materials and meet the test criteria for the USP24 Class VI 121ºC plastics.

MPM filters utilize high flow polypropylene membranes, capable of protecting your gas, air, and liquid processes with absolute ratings of 0.1 and 0.2 micron. GE Water & Process Technologies is your complete source for filters, crossflow membranes, housings and other filtration equipment.
Unit of Measure

Specifications

Type

 N/A MPM

Absolute Micron Rating

 N/A 0.1 µm

Nominal Cartridge Length

 N/A 10 in25.4 cm

End #1 Adapter

 N/A Open End Gasket

End #2 Adapter

 N/A 120 O-Ring
Elastomer Material1 N/A Buna-N EPDM Silicone Viton
Integrity Testing2 N/A ≤ 5 cc/min at 40 psi≤ 5 cc/min at 2.76 bar

Note

 N/A Trademark of General Electric Company; may be registered in one or more countries.

Materials of Construction

Filtration Media

 N/A Polypropylene Membrane

Support Layers

 N/A Polypropylene Microfiber

Core and Cage

 N/A Polypropylene

Endcaps and Adapters

 N/A Polypropylene

Dimensions

Nominal Outside Diameter

 N/A 2.75 in70 mm

Nominal Inside Diameter

 N/A 1.25 in31 mm

Effective Filtration Area

 N/A 7 ft²1 m²

Operational Limits

Maximum Forward Differential Pressure @ 70ºF (21ºC)

 N/A 60 psi4.1 bar

Maximum Reverse Differential Pressure @ 70ºF (21ºC)

 N/A 30 psi2.1 bar

Maximum Operating Temperature at 10 psid (0.7 bar) in Water

 N/A 140 ºF60 ºC

Typical Applications

N/A Memtrex PM filters are specifically designed for pure chemical filtration.

Typical applications include:

  • Vent and Process Air
  • Etchants, Photoresists and Developers
  • Solvents, Acids and Bases
  • Ultrapure Chemicals

    • General Properties

    N/A Memtrex PM filters are available the following absolute pore size micron ratings: 0.1 and 0.2 µm. Tables 1, 2, 3, 4, 5 and 6 show further details on materials of construction, dimensions, operational limits, integrity testing and flow performance in air and water.

    Additional Information

    N/A

    • Memtrex PM filters may be autoclaved or in situ steam sterilized (up to 253ºF [123ºC], 30 minute cycles) for a maximum accumulated exposure of 10 hours. Alternatively, the filters may be sanitized with compatible chemical agents.
    • GE certifies that the materials contained in its Memtrex PM pleated filters meet U.S. FDA requirements for food contact under the applicable regulations in 21 CFR. For further information, contact the GE technical services. Memtrex PM filters meet the test criteria for USP class VI-121ºC Plastics.
    • Aqueous extracts from Memtrex PM filters contain less than 0.25 EU/ml. The filters typically exhibit low levels of non-volatile residues. GE filter cartridges are designed and manufactured for resistance to a wide range of chemical solutions. Conditions will vary with each application and users should carefully verify chemical compatibility. Please contact your GE distributor for more information.

    • 1 PTFE and Viton are registered trademarks of DuPont.
    • 2 Air diffusion per 10" module after saturation with clean 100% IPA