argreen Process Technologies | From Coarse Straining Down to Microfiltration, Reverse Osmosis and Ultra Filtration
Pargreen Process Technologies
1224 Capitol Drive
Addison, IL. 60101
USA

Call: 800.323.2810
Fax: 630.628.3050
Email: sales@pargreen.com
Website: www.pargreen.com
Print Back
The Flotrex GF (FGF) filter (Figure 1) is an absolute rated, glass microfiber filter that is dependable and very efficient in the removal of Cryptosporidium and Giardia cysts. The filters do not leach any flavor-altering substances and are ideal for final filtration applications. FGF filters havemore
Unit of Measure

Specifications

Type

FGF

Absolute Micron Rating

0.45 µm

Nominal Cartridge Length

10 in25 cm
End #1 Adapter1 Open End Gasket

End #2 Adapter

120 O-Ring
Elastomer Material2 Buna-N EPDM Silicone Viton

Note

Trademark of General Electric Company; may be registered in one or more countries

Materials of Construction

Filtration Media

Acrylic Resin-Bonded Glass Microfiber

Support Layers

Polypropylene Microfiber

Core and Cage

Polypropylene

Endcaps and Adapters

Polypropylene

Dimensions

Filter Model

FGF94

Nominal Outside Diameter

2.75 in70 mm

Nominal Inside Diameter

1.25 in31 mm

Effective Filtration Area

4 ft²0 m²

Operational Limits

Maximum Forward Differential Pressure @ 70ºF (21ºC)

60 psi4.1 bar

Maximum Reverse Differential Pressure @ 70ºF (21ºC)

30 psi2.1 bar

Maximum Operating Temperature at 10 psid (0.69 bar) in Water

180 ºF82 ºC

ANSI/NSF Standard 53 Performance Requirements

Substance

Cyst

Influent Challenge Concentration

Minimum 50000/L

Reduction Requirement

99.95%

Applications

N/A Flotrex GF filters are specifically designed for high throughput and long service life. Typical applications include:

  • Final Filtration for Bottled Water
  • Prefiltration of Pharmaceuticals and Biologicals
  • Cosmetic Oil, Gel and Shampoo Filtration
  • Beverage Clarification
  • Paints and Coatings
  • Ink

  • General Properties

    N/A Flotrex GF filters are available the following absolute pore size micron ratings: 0.45 and 3.0 µm and 1.0 um which is NSF Standard 53 certified. Tables 1, 2, 3 and 4 show further details on materials of construction, dimensions, operational limits and flow performance in air and water.

    Additional Information

    N/A

    • Flotrex GF filters may be autoclaved or in situ steam sterilized (up to 257ºF [125ºC] 30-minute cycles) for a maximum accumulated exposure of 10 hours. Alternatively, the filters may be sanitized with compatible chemical agents.
    • GE certifies that the materials contained in its Flotrex GF pleated filters meet US FDA requirements for food contact under the applicable regulations in 21 CFR. For further information, contact GE technical services. Flotrex GF filters meet the test criteria for USP Class VI-121ºC Plastics.
    • Aqueous extracts from Flotrex GF filters contain less than 0.25 EU/ml. The filters typically exhibit low levels of non-volatile residues.
    • GE Filter cartridges are designed and manufactured for resistance to a wide range of chemical solutions. Conditions will vary with each application and users should carefully verify chemical compatibility. Please contact your GE distributor for more information.

      The Flotrex-GF 1.0 micron filter has been tested according to ANSI/NSF Standard 53 for reduction of the substances listed below. The concentration of the indicated substances entering the filter was reduced to a concentration less than or equal to the permissible limits for leaving the filter, as specified in ANSI/NSF Standard 53. Testing was performed under standard laboratory conditions. Actual performance may vary. Table 5 shows ANSI/NSF Standard 53 standards used in the performance testing.

    • 1 222 O-Ring Stainless Steel Insert or 226 O-Ring Stainless Steel Insert Adapters normally require Closed End Cap or Fin Adapters.
    • 2 PTFE and Viton are registered trademarks of DuPont.