argreen Process Technologies | From Coarse Straining Down to Microfiltration, Reverse Osmosis and Ultra Filtration
Pargreen Process Technologies
1224 Capitol Drive
Addison, IL. 60101
USA

Call: 800.323.2810
Fax: 630.628.3050
Email: sales@pargreen.com
Website: www.pargreen.com
Print Back
Memtrex MP (MMP) filters (Figure 1), constructed with hydrophilic polyethersulfone membranes and all polypropylene components, exhibit both enhanced throughput and reliable particle retention for superior performance in most applications. MMP filters are compatible with a broad range of chemicalsmore
Unit of Measure

Specifications

Absolute Micron Rating

0.1 µm

Nominal Cartridge Length

10 in25 cm
End #1 Adapter1 226 O-Ring

End #2 Adapter

120 O-Ring
Elastomer Material2 Buna-N EPDM PTFE Encapsulated Viton Silicone Viton
Integrity Testing3 ≤ 45 cc/min at 50 psig≤ 45 cc/min at 3.4 bar

Note

Trademark of General Electric Company; may be registered in one or more countries.

Materials of Construction

Filtration Media

Hydrophilic Polyethersulfone Membrane

Support Layers

Polypropylene Microfiber

Core and Cage

Polypropylene

Endcaps and Adapters

Polypropylene

Dimensions

Nominal Outside Diameter

2.75 in70 mm

Nominal Inside Diameter

1.25 in31 mm

Effective Filtration Area

8 ft²1 m²

Operational Limits

Maximum Forward Differential Pressure @ 70ºF (21ºC)

60 psid4.2 bar

Maximum Reverse Differential Pressure @ 70ºF (21ºC)

30 psid2.1 bar

Maximum Operating Temperature at 10 psid (0.7 bar) in Water

180 ºF82 ºC

Typical Applications

N/A MMP filters are suitable for a broad range of applications, including filtration of:

  • Inks and dyes
  • Acids, bases, and oxidants
  • Process water
  • Pharmaceutical preparations
  • Serums and tissue culture media

  • General Properties

    N/A Memtrex MP filters are available the following absolute pore size micron ratings: 0.1, 0.2, 0.45 and 0.65 µm. Tables 1, 2, 3, 4 and 5 show further details on materials of construction, dimensions, operational limits, integrity testing and flow performance.

    Additional Information

    N/A

    • Memtrex MP filters may be autoclaved or in situ steam sterilized (up to 257ºF [125ºC], 30-minute cycles) for a maximum accumulated exposure of 10 hours. Filters which are steam sterilized must have stainless steel insert supported o-ring adaptors. Alternatively, the filters may be sanitized with compatible chemical agents.
    • GE certifies that the material contained in its Memtrex MP pleated filters meet U.S. FDA requirements for food contact under the applicable regulations in 21 CFR. For further information, contact GE technical services. Memtrex MP filters meet the test criteria for USP class VI-121ºC Plastics
    • Aqueous extracts from Memtrex MP filters contain less than 0.25 EU/ml. The filters typically exhibit low levels of non-volatile residues.
    • GE filter cartridges are designed and manufactured for resistance to a wide range of chemical solutions. Conditions will vary with each application and users should carefully verify chemical compatibility. Please contact your GE distributor for more information.

    • 1 222 O-Ring Stainless Steel Support Ring & 226 O-Ring Stainless Steel Support Ring Adapters normally require Closed End Cap & Fin Adapters.
    • 2 PTFE and Viton ore registered trademarks of DuPont.
    • 3 Air diffusion per 10" module after saturation with clean water