argreen Process Technologies | From Coarse Straining Down to Microfiltration, Reverse Osmosis and Ultra Filtration
Pargreen Process Technologies
1224 Capitol Drive
Addison, IL. 60101
USA

Call: 800.323.2810
Fax: 630.628.3050
Email: sales@pargreen.com
Website: www.pargreen.com
Print Back
Polypropylene Membrane Media Filter Cartridges Engineered and Manufactured for Cost Effective Filtration

GPM grade Polypropylene Membrane cartridges are designed for general purpose use wherever a cost effective membrane filter is required. Designed to hold the maximum amount of filter media that can be completely and effectively utilized in a cartridge, GPM filters lower the cost of filtration . GPM cartridges are flushed with 17+ megohm-cm water to remove potential extraneous manufacturing debris. These cartridge modules are also individually tested for integrity. Priced below special purpose cartridges, GPM cartridges are still manufactured with the same careful attention to both quality and performance. Often used in place of PTFE Membrane because of lower cost and no undesirable extractables
Unit of Measure

Specifications

Pore size

N/A 0.10 µm

316 SS Ring

N/A No Ring

Cartridge Length

N/A 9.75 in24.6 cm

End Caps

N/A 020 O-ring / Plug 213/119 Internal O-ring / Plug 213/119 Internal O-ring DOE 2-222 O-ring / Flat 2-222 O-ring / Plug 2-222 O-ring / Spear 2-222 O-ring 3 Tab / Flat 2-222 O-ring 3 Tab / Spear 2-223 O-ring / Flat 2-223 O-ring / Spear 2-226 O-ring / Flat 2-226 O-ring / Spear Flat Gasket / Plug Flat Gasket, DOE

Flow Rate

N/A 0.75 gpm>22 SCFM/psid/10 inch cartridge

Gas Retention

N/A 0.01 µm

Construction Materials

Filtration Media

N/A Polypropylene

Filtration Media Support Material

N/A Polypropylene

End Caps Material

N/A Polypropylene

Center Core Material

N/A Polypropylene

Outer Support Cage Material

N/A Polypropylene

Sealing Method

N/A Thermal Bonding

O-Rings Material

N/A Buna EP PTFE® Encapsulated Silicone PTFE® Encapsulated Viton® Silicone Viton®

Note

N/A All materials of construction are FDA accepted. Final assemblies have been validated to pass USP class 6 Toxicology extractable tests, oxidizable substances for plastics, endotoxin level and other quality tests.

Maximum Operating Parameters

Forward Differential Pressure at 20ºC

N/A 50 psi3.4 bar

Reverse Differential Pressure at 20ºC

N/A 40 psi2.7 bar

Operating Temperature at 10 psid (0.69 bar) in Water

N/A 180 ºF82 ºC

Recommended Change Out Pressure

N/A 35 psid2.4 bar

Dimensions

Nominal Length

N/A 5 to 40 in12.7 to 101.6 cm

Nominal Outside Diameter

N/A 2.75 in7.0 cm

Filtration Area Per 10" Length

N/A 7.0 ft²0.65 m²

Sanitization / Sterilization

Filtered Hot Water

N/A 194 ºF90 ºC

Chemical Sanitization

N/A Industry standard concentrations of hydrogen peroxide, paracetic acid, sodium hypochlorite and other selected chemicals. Sanitization protocols designed to extend the useful life of GPM cartridges are available from Critical Process Filtration, Inc.

Integrity Test Information

Air Diffusion Rate1 N/A ≤ 50 cc/min at 40 psi≤ 50 cc/min at 2756 mbar

Applications

N/A Filtration of:

  • Etchants
  • Tank Vents
  • Solvents
  • Acids & Bases
  • Gases
  • Compressed Air
  • Chemicals
  • Fermentation Air

Validation

N/A GPM grade cartridges are validated using modified HIMA protocols.

Flow Rate

N/A See the Flow Rate table in more image which represents typical water flow at a one psi (69 mbar) pressure differential across a single 10-inch cartridge element. The test fluid is water at ambient temperature. Extrapolation for housings with multiple elements and higher pressure drops is acceptable, but as flows increase the pressure drop of the housing becomes more apparent.

Quality Standards

N/A Our goal is to ensure our customers the greatest possible value for their filtration dollar. We achieve both low cost manufacture and high quality by employing state of the art manufacturing equipment. This computer-controlled equipment is highly automated, reducing hand operations that compromise quality. Each operation, including assembly, testing, cleaning, drying and packaging, is done in appropriately rated clean rooms. Critical Process Filtration manages an ISO 9000 facility that produces validated products to rigorous standards. Manufacturing is controlled using sophisticated MRP software that is networked to work stations in manufacturing centers and inspection points. During the manufacturing and inspection processes, data is collected "real time" from machinery and measuring instruments. This allows variable and attribute data to be quickly and easily analyzed to facilitate constant improvements in both quality and cost.

Total Performance

N/A Critical Process Filtration, Inc. is a vertically integrated supplier of filtration products and services to industries in which filtration is considered to be a critical part of the manufacturing process. We manufacture a complete line of products to help you achieve all your filtration requirements from a single source.

  • 1 (per 10-inch length) (water wetted membrane)