Industry’s Filtration Partner
Request Information
The Selex (SX) cartridge filter (Figure 1) is a high precision graded density cartridge constructed of 100% pure polypropylene. Selex provides a very high particle retention efficiency that equates the performance of absolute rated filters. The patented Selex manufacturing process controls the density and fiber size, which are key to the filter’s performance and long life. Selex cartridge filters have sharp efficiency cutoff, fast rinse up for exceptional purity, and continuous, weld free lengths up to 40 inches (101.6 cm).
Unit of Measure

Specifications

Type

 N/A SXD

Absolute Micron Rating

 N/A 5 µm

Nominal Cartridge Length

 N/A 40 in101.6 cm

End #1 Adapter

 N/A 1 inch (25.4 cm) Open End Gasket 222 O-Ring 226 O-Ring Extended Care Standard Plain End

End #2 Adapter

 N/A 1 inch (25.4 cm) Open End Gasket Fin Self Seal Spring Solid End
Gasket Material1 N/A Santoprene
O-Rings Material2 N/A Buna EPDM Silicone Viton

Nominal Outside Diameter

 N/A 2.50 in6.4 cm

Nominal Inside Diameter

 N/A 1 in2.5 mm

Maximum Operating Temperature

 N/A 140 ºF60 ºC

Materials of Construction

Filtration Media

 N/A Polypropylene

Endcaps and Adapters

 N/A Polypropylene

Performance Specification for General Applications

Selex Grade

 N/A D

Removal Rating (µm) at Various Efficiencies (90%)

 N/A 1.5

Removal Rating (µm) at Various Efficiencies (95%)

 N/A 1.8

Removal Rating (µm) at Various Efficiencies (98%)

 N/A 2.9

Removal Rating (µm) at Various Efficiencies (99%)

 N/A 4.3

Removal Rating (µm) at Various Efficiencies (99.50%)

 N/A 5.0

Performance Specification for Critical Applications

Removal Rating (µm) Where β = 5000

 N/A 6.5

Note

N/A Removal efficiencies are reported for a given particle size, i.e. an efficiency of 99% at 3 microns means that the filter removes 99% of the particles that are 3 microns in size.

The Beta Ratio (β) is calculated as a measure of efficiency for all particles equal to or larger than the given micron size. A Beta Ratio (β) of 5000 represents the removal of 99.98% of all particles equal to or larger than the given micron size.

Trademark of General Electric Company; may be registered in one or more countries.

Typical Applications

N/A

  • Magnetic Media (CMP) - solvents, slurry/dispersion, Pre-Filter and Final Filter at Coater
  • Photographic - Incoming Water, Liquid Chemicals, Developer, Fixer, Stopper Solutions
  • Petrochemicals - Waterflood, Completion, Enhanced Oil Recovery, Amines
  • Chemical Process Industry - Reagent Grade Chemicals, Process Water
  • Pure Water - Pre-RO, Post- DI Resin Trap
  • Food and Beverage - Clarification, Process Water, Polishing Filter
  • Metal Finishing - Electrodeposition Paint, Precision Electroplating
  • Potable Water- Polishing Filter, Giardia Removal
  • Pharmaceuticals - Clarify Production Broths, Prefiltration
  • Oil and gas - well protection

    • General Properties

    N/A Selex filters are available the following absolute pore size micron ratings: 1, 3, 5, 10, 20 and 30 microns. Tables 1, 2, 3 and 4 show further details on materials of construction, dimensions, flow performance and performance specifications.

    Additional Information

    N/A Selex depth cartridge filters are made from thermally- bonded fibers of polypropylene. GE Water & Process Technologies certifies that it uses no resin binders, lubricants, antistatic or release agents or other additives in the manufacture of these cartridges, and that the resin used for manufacturing the filter media meets the food contact requirements of the U.S. FDA 21CFR regulations.

    When required, specify only FDA compliant sealing materials and end adapters.

    GE filter cartridges are designed and manufactured for resistance to a wide range of chemical solutions. Conditions will vary with each application and users should carefully verify chemical compatibility. Please contact your GE distributor for more information.

    • 1 When using filter types SXE, SXG, or SXD with a knife-edge seal, an elastomeric gasket is recommended to retain highest efficiencies possible.
      Santoprene is a registered trademark of Advanced Elastomer Systems, L.P.
    • 2 Viton is a registered trademark of DuPont Dow Elastomers L.L.C.